... | @@ -31,7 +31,7 @@ image::https://es.technikum-wien.at/openlab/openlab_wiki/wikis/img/sig_proc_osci |
... | @@ -31,7 +31,7 @@ image::https://es.technikum-wien.at/openlab/openlab_wiki/wikis/img/sig_proc_osci |
|
|
|
|
|
{empty} +
|
|
{empty} +
|
|
|
|
|
|
By applying the formula of a standard non-inverting op-amp, the gain level (AV ) can be calculated as shown in the following calculation.
|
|
By applying the formula of a standard non-inverting op-amp, the gain level (AV) can be calculated as shown in the following calculation.
|
|
|
|
|
|
{empty} +
|
|
{empty} +
|
|
|
|
|
... | @@ -43,7 +43,7 @@ In case of the OpenLab front-end the resistance of Rgadj is changed by switching |
... | @@ -43,7 +43,7 @@ In case of the OpenLab front-end the resistance of Rgadj is changed by switching |
|
Rgadj is changed by opening or closing the ground connection through bipolar transistors.
|
|
Rgadj is changed by opening or closing the ground connection through bipolar transistors.
|
|
Those transistors on the other hand, are controlled by a de-multiplexer which is directly accessed by the development board.
|
|
Those transistors on the other hand, are controlled by a de-multiplexer which is directly accessed by the development board.
|
|
This applies to the FPGA-based oscilloscope as well as to the microcontroller-based solution. +
|
|
This applies to the FPGA-based oscilloscope as well as to the microcontroller-based solution. +
|
|
The correct values of Rgadj , at each amplification stage, were calculated and summarized in table 5.
|
|
The correct values of Rgadj , at each amplification stage, were calculated and summarized in table 1.
|
|
This listing also mentions the gain of each amplification stage and at what input voltage range it is used for.
|
|
This listing also mentions the gain of each amplification stage and at what input voltage range it is used for.
|
|
|
|
|
|
{empty} +
|
|
{empty} +
|
... | @@ -52,7 +52,7 @@ image::https://es.technikum-wien.at/openlab/openlab_wiki/wikis/img/sig_proc_osci |
... | @@ -52,7 +52,7 @@ image::https://es.technikum-wien.at/openlab/openlab_wiki/wikis/img/sig_proc_osci |
|
|
|
|
|
{empty} +
|
|
{empty} +
|
|
|
|
|
|
As can be seen in table 5, the output voltage range of each amplification stage varies from stage to stage. This could be minimized by using resistors of a higher class.
|
|
As can be seen in table 1, the output voltage range of each amplification stage varies from stage to stage. This could be minimized by using resistors of a higher class.
|
|
The OpenLab oscilloscope uses resistors of the E12 or E24 series to reduce costs. This helps to achieve the low-cost status of the project. +
|
|
The OpenLab oscilloscope uses resistors of the E12 or E24 series to reduce costs. This helps to achieve the low-cost status of the project. +
|
|
Those variations of the output voltage are compensated in software to maintain correct measurements.
|
|
Those variations of the output voltage are compensated in software to maintain correct measurements.
|
|
|
|
|
... | @@ -67,7 +67,7 @@ image::https://es.technikum-wien.at/openlab/openlab_wiki/wikis/img/sig_proc_osci |
... | @@ -67,7 +67,7 @@ image::https://es.technikum-wien.at/openlab/openlab_wiki/wikis/img/sig_proc_osci |
|
|
|
|
|
{empty} +
|
|
{empty} +
|
|
|
|
|
|
The waveform drawn in red represents the input of stage 3. The output is shown by the blue signal. According to table 5, amplification stage 3 was selected.
|
|
The waveform drawn in red represents the input of stage 3. The output is shown by the blue signal. According to table 1, amplification stage 3 was selected.
|
|
This will amplify the input signal of stage 3 by a factor of 3.68.
|
|
This will amplify the input signal of stage 3 by a factor of 3.68.
|
|
|
|
|
|
== https://es.technikum-wien.at/openlab/openlab_wiki/wikis/home[Home] | https://es.technikum-wien.at/openlab/openlab_wiki/wikis/sig_proc_hardware[<Signal Processing Hardware] | https://es.technikum-wien.at/openlab/openlab_wiki/wikis/ETS_theory[Equivalent Time Sampling - Theory>] |
|
== https://es.technikum-wien.at/openlab/openlab_wiki/wikis/home[Home] | https://es.technikum-wien.at/openlab/openlab_wiki/wikis/sig_proc_hardware[<Signal Processing Hardware] | https://es.technikum-wien.at/openlab/openlab_wiki/wikis/ETS_theory[Equivalent Time Sampling - Theory>] |