getting-started-zybo.md

-Getting Started Zybo
\ No newline at end of file
+#### [Home](https://es.technikum-wien.at/iplat/testwiki/wikis/home) | [<Getting Started - Basys3](https://es.technikum-wien.at/iplat/testwiki/wikis/getting-started-basys3)
+
+***
+
+# 5. Getting Started - Zybo
+
+## 5.1 Introduction
+
+The following section presents a tutorial for the ZyboDevelopment Board. 
+
+### 5.1.1  Pre-requisites
+
+Following pre-requisites are necessary in order to work through this tutorial:
+
++ Vivado HLx 2015.4 (see [Vivado Toolchain](https://es.technikum-wien.at/iplat/testwiki/wikis/vivado-toolchain) for an installation guide)
++ ZyboDevelopment Board 
++ micro USB cable
+
+**Note:** Vivado 2016.1 was successfully tested with this tutorial.
+
+### 5.1.2 Download the Design files
+
+An archive with the design files can be downloaded [here](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-zybo/design-files/GettingStartedZybo.zip).
+
+Furthermore, download the [board definition files](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-zybodesign-files/BoardFiles.zip) for the Zybo development Board. Extract the archive and copy the folder **zybo** to following directory:
+
+$VIVADO_ROOT_DIR$/2015.4/data/boards/board_files
+
+## 5.2 Tutorial
+
+This section explains how to generate the FPGA hardware bitstream using the Xilinx Vivado tool. Then the project will be exported to Xinlinx SDK, where a simple blink led application will be created. Furthermore the board setup will be explained. Finally, the Bitstream will be flashed onto the FPGA and the application will be tested.
+
+### 5.2.1  Building the Bitstream
+
+_1. Launch Vivado:_
+
++ select **Start > All Programs > Xilinx Design Tools > Vivado 2015.4 > Vivado 2015.4**
+
+_2. Create new Project_
+
+Click on the **Create New Project** button in the quick start menu. Click **Next**.  Enter blink_led as the Project name. Click **Next**.
+
+**Note:** Do not use spaces or special characters in the project path.
+
+Select RTL Project. Make sure that the **Do not specify sources at this time** checkbox is **not** selected. Click **Next**.
+
+![](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-basys3/img/tutorial_basys1.png)
+
+Click on the **Add Files** Button. Browse to the previously downloaded and extracted zip folder. Select **blink_led.vhd** and click **OK**. Make sure that the **Copy sources into project** checkbox is selected and the target language and simulator language is set to VHDL. Click **Next** twice.
+
+![](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-basys3/img/tutorial_basys2.png)
+
+Click on the **Add Files** Button. Browse to the previously downloaded and extracted zip folder. Select **blink_led.xdc** and click **OK**. Make sure that the **Copy constraints files into project** checkbox is selected. Click **Next**.
+
+![](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-basys3/img/tutorial_basys3.png)
+
+In the search box type: **XC7A35TCPG236-1**. Select the Part and click **Next**.  
+
+![](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-basys3/img/tutorial_basys4.png)
+
+Click **Finish** to finish the project creation process.
+
+In the **Project Manager** toolbar click the **Generate Bitstream** button which can be found in the Program and Debug subsection. A window pops up. Click on **Yes**.
+
+![](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-basys3/img/tutorial_basys5.png)
+
+A window should pop up once the bitstream generation finished successfully. Click on **Cancel**.
+
+### 5.2.2 Board Setup
+
+Make sure that **JP2** is configured to use **USB** as power source. Furthermore, make sure **JP1** is configured to the **JTAG** mode. Insert a micro USB cable to **JC4** and connect it to your PC. Make sure that the switches **SW0 - SW15** are in the off position.
+
+ Finally, switch **SW16** to the on position. 
+
+![](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-basys3/img/tutorial_basys6.png)
+
+
+### 5.2.3 Test the Application
+
+In the **Project Manager** toolbar click the **Open Hardware Manager** button which can be found in the Program and Debug subsection.
+
+![](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-basys3/img/tutorial_basys7.png)
+
+Click on the **Auto Connect** submenu of the **Open target** button.
+
+![](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-basys3/img/tutorial_basys8.png)
+
+Finally, click on **Program Device -> xc7a35t_0**. A window pops up. Click on **Program**.
+
+![](https://es.technikum-wien.at/iplat/testwiki/raw/master/getting-started-basys3/img/tutorial_basys9.png)
+
+After the bitstream is downloaded successfully the **DONE** LED of the Board should light up.  Switch **SW0** into the up position. **LD0** starts to blink. Switch **SW0 - SW15** into the up position. **LD0-LD15** blink synchronously.
+
+This concludes the Basys3 Getting Started tutorial.
+
+
+***
+
+#### [Home](https://es.technikum-wien.at/iplat/testwiki/wikis/home) | [<Getting Started - Basys3](https://es.technikum-wien.at/iplat/testwiki/wikis/getting-started-basys3)