Commit 368b547d authored by Christian Fibich's avatar Christian Fibich Committed by Stefan Tauner
Browse files

VGA TMR Demo: Zybo

Added trigger to UM.

Added constraint files for Vivado.

Added FIU names to cfg
parent 73957fdd
; FIJI::ConfigSorted 0.1
; Thu Apr 13 16:27:51 2017
; Thu Sep 7 17:20:35 2017
[CONSTS]
BAUDRATE=115200
......@@ -24,6 +24,7 @@ OUTPUT_DIR=.
RST_DUT_IN_ACT=1
RST_DUT_IN_DUR=1
RST_DUT_IN_EN=0
RST_DUT_IN_NAME=
RST_DUT_OUT_ACT=1
RST_DUT_OUT_EN=1
RST_DUT_OUT_NAME="spriteflyer_top/s_reset_x_i_c"
......@@ -46,6 +47,7 @@ DRIVER_PATH="spriteflyer_sprite_2_1/\\s_sprite_line_Z[0] /Q"
DRIVER_TYPE=PIN
FAULT_MODEL=RUNTIME
LFSR_MASK=0x1
NAME=Sprite Line
NET_NAME="spriteflyer_top/\\generate_tmr_partitions.0.i_sprite /s_sprite_line[0]"
[FIU1]
......@@ -53,6 +55,7 @@ DRIVER_PATH="spriteflyer_sprite_2_1/s_x_state_Z/Q"
DRIVER_TYPE=PIN
FAULT_MODEL=RUNTIME
LFSR_MASK=0x2
NAME=X State
NET_NAME="spriteflyer_top/\\generate_tmr_partitions.0.i_sprite /s_x_state"
[FIU2]
......@@ -60,6 +63,7 @@ DRIVER_PATH="spriteflyer_voter_6/s_green_tmr_partitions"
DRIVER_TYPE=PORT
FAULT_MODEL=RUNTIME
LFSR_MASK=0x3
NAME=VGA Green
NET_NAME="spriteflyer_top/i_voter_green/s_green_tmr_partitions[5]"
create_clock -period 8.000 -name s_clk_i -waveform {0.000 4.000} [get_ports -filter { NAME =~ "*clk*" && DIRECTION == "IN" }]
set_property IOSTANDARD LVCMOS33 [get_ports s_fiji_rx_i]
set_property IOSTANDARD LVCMOS33 [get_ports s_fiji_tx_o]
set_property SLEW FAST [get_ports s_fiji_tx_o]
set_property PACKAGE_PIN V12 [get_ports s_fiji_rx_i]
set_property PACKAGE_PIN W16 [get_ports s_fiji_tx_o]
set_property PACKAGE_PIN P16 [get_ports s_fiji_trig_ext_i]
set_property IOSTANDARD LVCMOS33 [get_ports s_fiji_trig_ext_i]
......@@ -76,7 +76,7 @@ In a real-world design the states of the redundant units would usually be determ
The design generates a 640x480 @ 25Mhz VGA signal.
\item The dip-switch SW0 controls if TMR is enabled.
\item BTN0 resets the design when pressed.
% FIXME: External Trigger
\item The external trigger is activated when BTN1 is pressed.
\item The LEDs above the dip switches (LD0-LD3) show the error detection state:
\begin{itemize}
\item LD0 shows if any error has been detected.
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment